TOTANI Saldatrici per buste sotto vuoto // Pouch and vacuum bag making // Bag making // Macchine Flexo Usate // Tecno Converting 2000 S.r.l.

** SOLD **

Codice Macchina: PO13
Manufacturer: TOTANI
Year: 2013
Type of sealing/bags: 3 side weld
Lunghezza sacchetti: 120 to 270 mm
Larghezza sacchetti: 60 to 250 mm
Ulteriori informazioni: three sided; stand up pouches; zipper and plow gusset
Ulteriori informazioni: Standing pouch: -crosswise simultaneous two—line printing Pouch dimensions : Bottom gusset depth 20 to 45 (70 m) ; Bottom punch diameter ø12 to ø20 rtm Film roll dimensions :Maximum diameter ø600 rm (rolled on 3—inch pipe) Minimum width 150 (2 shafts horizontal ax±s type Maximum diameterø600 rm (roiled on 3-ånch pipe) width1100 for two—line pouch) Maximun weight 40' kg Two bottom •gusset punches 2 units The standard punch diameter is ø12 to ø20 nun. When the punch diameter is ø20 rm or less with holes provided ae intervals of 30 rtm, it can be used as a two-hole punch. Four bottom gusset punches are provided. One bottom seal photoelectric sensor (reflection type One bottom film folding device (triangle plate type for two-line operation) Two bottom film Rewinding devices (with forced unwinding unit) Speed control by dancer roller position detection pinch roll method. Two horizontal axis type bottom film roll sections These devices are provided with constant tension powder brake as standård without •requiring any adjustment from the start to the •end of the film roll winding. One bottom film guide spatula (for two—line operation) Two—hole punch for punch diameters and hole pitches according to your requirements Bottom film joint detector The bottom film joint: detector allows the pouch containing the bottom joint to be identified by the cutter •stop operation (two• pouches not cut) The corner cutter is installed on the cross heater unit. to cut four corners of the pouch with punches; it is designed for two—line products. C'hese punches can be produced in various shapes they are inside the diameter of ø16 Bottom gusset web section for 300 nun bottom film width Maximum bottom film diameter ; ø600 ram (sarne as standard) Maximum bottom film width 300 mm The standing pouch bottom heater ig mounted on the standard longitudinal heater Two units can be mounted. When three or more longitudinal heaters are used, the two outermost heaters serve as standing pouch bottom heaters These heaters ate connected at the bottom to facilitate adiustment of the bottom seal bar position as follows: (1)Movement in the right angle to film flow with the relative positions of tyr&. upper and lower bottom seal bars maintained. (2Adjustment of inclination of the bottom seal bar to film flow with the relative positions of the upper and lower bottom seal bars maintained. (3)Fine adjustnent of the position in the flow direction in two—line operation mode, with the relative positions of the upper and lower bottom seal bars maintained. When the machine stops, the lower heater automatically goes dom 20 to prevent the film from sticking due to heat.

Codice Macchina	PO13
Manufacturer	TOTANI
Year	2013
Type of sealing/bags	3 side weld
Lunghezza sacchetti	120 to 270 mm
Larghezza sacchetti	60 to 250 mm
Ulteriori informazioni	three sided; stand up pouches; zipper and plow gusset
Ulteriori informazioni	Standing pouch: -crosswise simultaneous two—line printing Pouch dimensions : Bottom gusset depth 20 to 45 (70 m) ; Bottom punch diameter ø12 to ø20 rtm Film roll dimensions :Maximum diameter ø600 rm (rolled on 3—inch pipe) Minimum width 150 (2 shafts horizontal ax±s type Maximum diameterø600 rm (roiled on 3-ånch pipe) width1100 for two—line pouch) Maximun weight 40' kg Two bottom •gusset punches 2 units The standard punch diameter is ø12 to ø20 nun. When the punch diameter is ø20 rm or less with holes provided ae intervals of 30 rtm, it can be used as a two-hole punch. Four bottom gusset punches are provided. One bottom seal photoelectric sensor (reflection type One bottom film folding device (triangle plate type for two-line operation) Two bottom film Rewinding devices (with forced unwinding unit) Speed control by dancer roller position detection pinch roll method. Two horizontal axis type bottom film roll sections These devices are provided with constant tension powder brake as standård without •requiring any adjustment from the start to the •end of the film roll winding. One bottom film guide spatula (for two—line operation) Two—hole punch for punch diameters and hole pitches according to your requirements Bottom film joint detector The bottom film joint: detector allows the pouch containing the bottom joint to be identified by the cutter •stop operation (two• pouches not cut) The corner cutter is installed on the cross heater unit. to cut four corners of the pouch with punches; it is designed for two—line products. C'hese punches can be produced in various shapes they are inside the diameter of ø16 Bottom gusset web section for 300 nun bottom film width Maximum bottom film diameter ; ø600 ram (sarne as standard) Maximum bottom film width 300 mm The standing pouch bottom heater ig mounted on the standard longitudinal heater Two units can be mounted. When three or more longitudinal heaters are used, the two outermost heaters serve as standing pouch bottom heaters These heaters ate connected at the bottom to facilitate adiustment of the bottom seal bar position as follows: (1)Movement in the right angle to film flow with the relative positions of tyr&. upper and lower bottom seal bars maintained. (2Adjustment of inclination of the bottom seal bar to film flow with the relative positions of the upper and lower bottom seal bars maintained. (3)Fine adjustnent of the position in the flow direction in two—line operation mode, with the relative positions of the upper and lower bottom seal bars maintained. When the machine stops, the lower heater automatically goes dom 20 to prevent the film from sticking due to heat.